Standard Epoxies
Infusion Epoxies
PRO-SET® Infusion epoxies result in lightweight, high performance composites that will withstand long-term cyclic loading in the harshest environments.
PRO-SET Infusion epoxies are super-low viscosity systems with a range of hardeners to meet the demands of modern infusion processes. They develop excellent physical properties at room temperature and may be post-cured to further enhance performance.
A complete range of hardeners to complement the infusion resin
| PRO-SET Infusion Epoxies | |
|---|---|
| Resins | |
| Infusion Resin | INF-114 |
| Hardeners | |
| Fast Infusion Hardener | INF-210 |
| Medium Infusion Hardener | INF-211 |
| Slow Infusion Hardener | INF-212 |
| Extra Slow Infusion Hardener | INF-213 |
Hardeners may be blended for targeted cure time
Match the correct resin to your exact requirements
This guide compares the typical physical properties. These test specimens are cured at room temperature to gelation and at 82°C for eight hours, unless otherwise noted. Neat epoxy samples are used for testing. These are typical values, not to be construed as specifications.
| Property | Standard | units | INF-114 Resin¹ |
|---|---|---|---|
| Mix Ratio by Volume | R:H | 3:1 | |
| Mix Ratio by Weight | R:H | 3.65:1 | |
| Mixed Viscosity @25℃ | ASTM D2196 | mPas | -245 |
| Mixed Viscosity @22℃ | gcm-3 | -1.14 | |
| Compression Yield | ASTM D695 | MPa | -97 |
| Tensile Strength | ASTM D638 | MPa | -71.3 |
| Tensile Modulus | ASTM D638 | GPa | -3.38 |
| Tensile Elongation | ASTM D638 | % | -4.95 |
| Flexural Strength | ASTM D790 | MPa | -123.7 |
| Flexural Modulus | ASTM D790 | GPa | -3.19 |
| Tg Ultimate via DMA² | ASTM E1640³ | ℃ | >85.2 |
As of press time, TBD values are undergoing testing.
¹Average of properties for combinations with INF-210, INF-211, INF-212 and INF-213 Hardeners.
2Additional post cure may be required; contact us for details.
31 HZ, 3°C per minute
Match the correct hardener to your exact requirements
| Property | Standard | INF-210 Hardener |
INF-211 Hardener |
INF-212 Hardener |
INF-213 Hardener |
|---|---|---|---|---|---|
| 150g Pot Life @ 25℃ | ASTM D2471 | 27min | 122 min | 185 min | 262 min |
| 500g Pot Life @ 25℃ | ASTM D2471 | 25 min | 85 min | 132 min | 175 min |
| Approx. working time @ 25℃ | 75-90 min | 3-4 hr | 6-7 hr | 10 hr |
Downloadable technical datasheets
PRO-SET INF-114 with INF-210 Fast Cure Infusion Epoxy
PRO-SET INF-114 with INF-211 Medium Cure Infusion Epoxy
PRO-SET INF-114 with INF-212 Slow Cure Infusion Epoxy
PRO-SET INF-114 with INF-213 Extra Slow Cure Infusion Epoxy
PRO-SET INF-114 with INF-249-HT Medium Cure High Tg Infusion Epoxy TDS
DNV GL Approval. PRO-SET INF-114 resin with INF-210, INF-211, INF-212 and INF-213 hardeners combinations have all been awarded Type Approval by DNV GL.
